276°
Posted 20 hours ago

BISupply Pallet Buster Tool with Handle 3 Section 41in - Deck Wrecker Dismantler Wood Pallet Tool Breaker Pry Bar Puller

£24.335£48.67Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Step 3: Do not use a crowbar to try to twist the boards apart. You will make marks on them, and some will splinter. Instead, put the pallet on a flat surface like a floor, and place a piece of wood under the board, just next to the stringer you want to push off. Then with another piece of wood, you tap a few times on the stringer from above, and it will come off easily, without breaking the stringer or the boards it was attached to. There will be no nails in the stringers and only short nails on the boards. You can remove them easily with a small hammer and a prybar. For example, the PalletSaw-W can be combined with combination with the Cekamon EndSaw. A machine that trims boards of used pallets. Even when the boards contain rests of nails.

To remove the end slats, simply use a length of 3×2 timber and lay it roughly 3 or so inches away from the slat and then use this as a fulcrum to lever against to remove the end slats Whichever method you use from the list above, once you have broken your pallets down into individual slats you will have one last remaining job to do and that’s denail them. Position your levering timbers either side of each slat and move them outwards until they touch your new fulcrum timbers then simply move your levering timbers outwards as you did in the steps above. Repeat for any further slats that need removingNext, find 2 lengths of either 3×2 or 4×2 inch timbers that are roughly 3 feet long each. These are going to be used as levering bars For 50-75 pallet per hour you can remove broken parts or you can complete dismantle 20-40 pallets per hour Using a reciprocating saw to dismantle a pallet is best done with the pallet standing up on its edge so you need to ensure it’s stable and solid and doesn’t wobble and flap about.

For any slats that cross each other, these may still be joined together. In this case use a prying bar or sturdy flat edge screwdriver to prise them apart Many DIY jobs and projects in the home involve timber and if you are working to a budget a great source of, in many cases, free timber is the common pallet, but to use the timber you first have to dismantle the pallet. The PalletSaw-W is THE band saw for every pallet company and all sorts of pallets. With this pallet shredder machine you either dismantle the pallet completely or replace its broken parts in an efficient way.

The PalletSaw-W is equipped with large wheels covered with synthetic material for longer durability Stand pallet upright and screw it to another pallet laying on the floor at 90° so that its solid and supported DEWALT 20V MAX Reciprocating Saw, 3,000 Strokes Per Minute, Variable Speed Trigger, Bare Tool Only... As the timber is of better quality it’s nicer to work with and also makes the job of breaking the pallet down a fair bit easier. With all possible slats removed it’s now time to remove the slats that we couldn’t previously. To do this, find a further 2 lengths of 3×2 roughly 2 feet in length. Place these either side of a slat roughly 3 inches away.

The length of the tines depends on your pallets but the ones above are 150mm (6”) long; although for most pallets, 112mm (4 1/2”) or so is sufficient. The choice of removing or keeping the nails depends on you! Keeping the nails adds a certain charm and specific rustic characteristic to the pallet craft you’re making. However, sometimes you’re making a very finished piece where nails won’t add to the appeal. It’s strictly up to you. No matter what you do, take care when working with pallets. Don’t forget that the nails are in place if you leave them – they could cause significant damage to your tools – and to YOU. ALWAYS wear protective gear, especially goggles or safety glasses when working with pallets. Breaking a pallet down using a reciprocating saw is one of the better techniques and if done with care, pretty much guarantees no damage to any slats.Unfortunately this is not a nice job and if you have loads of slats to denail, one that can take quite a while. With the use of a robot we achieved tailor-made solutions for dismantling pallets. The robot saws the broken board or pallet foot.

Milwaukee M18 Fuel Sawzall Brushless Cordless Reciprocating Saw - No Charger, No Battery, Bare Tool... With both side of slats cut through the final job now is to simply lever the slats away at the centre. To do this use a breaker bar or large sturdy screwdriver to prise the slats up and off. To get your screwdriver or pry bar under the slat simply wiggle the slat up and down and this will begin to pull it off Angle both prying/levering timbers outwards away from each other so that the ends underneath the slat you are removing come together at the centre of the slat. The underside of each prying timber will now sit against the top edge of the slat to the side of it. This will allow us to lever upwards, using these slats as a fulcrum p.s. please excuse the ‘basic’ nature of the video, you won’t see me in it, as I have a face made for radio…. 🙂

Machines Available

DEWALT Reciprocating Saw, 12 Amp, 2,900 RPM, 4-Position Blade Clamp, Variable Speed Trigger, Corded...

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment